COMPLETE 6 Volt LED Lighting System For 2 Cycle Motorized Bicycles LED Headlight

Description

Bicycle Motorized Bicycle Lighting
Bicycles and Motorized Bikes...Avoid Accidents...Avoid Tickets...Get Lights!
Motorized Bicycle Lighting
6 Volt Mini-Generator
12 Volt Mini-Generator Max
6 Volt Mini-Generator With Switch
12 Volt Mini-Generator With Switch
6 Volt Mini-Gen for Pull Start Engines
12 Volt Mini-Gen Max for Pull Start Engines
Complete 6 Volt Lighting System LS-1
Complete 7.2 Volt Lighting System LS-2
Complete 12 Volt Lighting System LS-3
Enclosed Light Switch SPST
Enclosed Light Switch SPDT
Encased 6 Volt SLA Battery
Encased 7.2 Volts AA Battery Pack
Encased 14.4 Volts AA Battery Pack
6 Volt Mini-Charger For LS-1 and LS-2
12 Volt Mini-Charger for LS-3
Magneto Coil Mini Charger
Magneto Coil Lighting System
Heavy Duty Headlight Bracket
Heavy Duty Tail Light Bracket
New 6 Volt LED Lighting System For Motorized Bicycles
This is a self sufficient, 6 Volt LED Headlight System.
System is designed to work with 2 cycle engine motorized bicycles.
The main component is the Mini-Generator which produces AC voltage while engine is running.
The other two important components are the Mini-Charger and the 6 Volt encased SLA battery.
While engine is running, the Mini-Gen sends current to the Mini-Charger which converts the AC volts to DC volts and charge the battery.
The battery will be charged while riding, and maintain a full charge without overcharging.
The complete system includes a Mini-Generator, Mini-Charger, encased 6 volt 1.2Ah SLA battery, light switch, LED Headlight, LED tail light, extra wire and attachments.
The Headlight is custom made from polyvinyl chloride material with a high power 5 Watt LED bulb.
The Headlight has bubble glass lens and has a frame grounded black wire and a positive green wire.
The Mini-Charger features a 2 inch long black box with built in battery charging circuit.
The charging circuit is permanently encapsulated to protect it from moisture & vibration.
The green 5MM LED light on Mini-Charger will light up to indicate current flow.
This Headlight system is self sufficient and also very energy efficient.
Installing the Mini-Generator is simple, and all instructions are included.
Just remove the magneto cover, then remove the two rear screws.
The photo seen demonstrates how the Mini-Generator is installed into engine magneto case.
The Mini-Generator works off of the residual magnetic force of the spinning magnet when engine runs.
This Mini-Generator will produce nominal AC volts of 6 to 8 volts and more, dependig on engine speeds.
After Mini-Gen is installed, simply insert wire as seen in photo, making sure it won't get pinched.
All instructions and specs are included with the Mini-Generator purchase.
Installation and operating instructions are included.
After installing Mini-Generator, the Mini-Charger can be attached to bicycle's seat post, and ground wire (black wire with ring terminal) should be grounded to engine (as seen in photo).
An easy way to install the ground wire is by using the carburetor intake nut (as seen in photo).
Just loose one of the carburetor intake nuts and attach the ground wire ring terminal.
The red wire from Mini-Charger should be routed to lower frame and connected to Mini-Generator.
The Mini-Charger has two (2) black wires; one is grounded and the other connects to battery ground.
Mini-Charger also has two (2) Red wires; the longer one is for input from Mini-Generator.
The other red wire (fused wire) on Mini-Charger connects to battery positive terminal.
The fifth (5th) wire on Mini-Charger is a green wire which connects to light switch.
Small strips of black duct tape can be very effective in organizing and also securing these wires.
A foot of wire cover (split loom) is included which might help with wire arrangements.
NOTE:
Images are for demonstration only! Wires will be sorted and tucked away. Your results will be far better!
After the Mini-Charger is installed on seat post and ground wire is connected, the 6 volt SLA battery can now be attached to bicycle seat post opposite the Mini-Charger.
The encased 6 Volt SLA Battery may also be attached elsewhere if desired.
Just use the available cable ties and attach encased batery to bicycle seat post or other place.
After battery is attached, the positive and negative wires can then be connected to red and black wires of Mini-Charger.
Battery will be charged up by Mini-Charger while engine is running.
After connecting Mini-Charger and battery, all wires should be neatly tucked away and secured. It might be a good idea to keep the fused portion accessable.
Duct tape can be placed on seat post before installing Mini-Charger and battery pack. This can help prevent items from sliding down due to vibration, also protect frame from scratches.
Battery case is approx. 4.7" X 2.6" X 1.55 inches.
The photos are for demonstration purposes only! Your installation will look much better!
This photo illustrates some wires being connected and tucked away.
Also note the top cable tie for battery is placed above the Mini-Charger cable tie. This provides extra support for the battery pack.
Battery case has a 1.2 Ah SLA battery within.
The wire cover/split loom is used on a portion of Mini-Charger wire and fastened to frame with duct tape.
The red wires for Mini-Gen/Charger connection can be seen connected at lower frame.
The green wire should be positioned upward, and will be later connected to light switch on handle bar.
Mini-Charger will keep the battery charged up so that headlight will be available at the click of a switch.
Your setup will look much better because you will arrange these wires to suit your own unique taste!
After all charging and battery circuits are connected, the headlight can now be connected.
This photo is for illustration of the light switch and LED headlight.
This is a 6 volt LED headlight designed to run on 6 to 7 volts of battery power.
Do not use a 12 volt battery with this headlight.
This headlight is custom made from polyvinyl chloride (plastic like) material and has a bubble glass lens which adds some safet (you can be notice by drivers at a side angle).
A domed shape glass cover is used and will provide some peripheral vision to side approaching traffic.
The short black wire on headlight is grounded to headlight bracket, and longer green wire connects to light switch.
The black (ground) wire is grounded directly to metal clamp and positive wire is connected to green wire coming out of light switch.
Headlight size is approximately 2.0 inch diameter x 2 inches deep.
NOTE: A layer of duct tape can be used to help secure light switch from sliding on handle bar. Cable ties should be trimmed after installation.
This photo demonstrates how the connector wires for Mini-Charger and tail light can be routed along upper bicycle frame.
The two 30 inch long wires will connect Mini-Charger green positive wire to light switch, and black wire from light switch output to tail light.
The Mini-Charger green wire will remain "hot" (with positive battery voltage) as long as battery is connected.
Try not to let the green wire rub on bicycle frame as it could cause the fuse in Mini-Charger to blow.
If the 2 amp fuse in Mini-Charger is blown, the green wire will still provide some power from Mini-Gen if bike is running, but may not be equivalent to battery power.
If light does not come on without bike running, fuse might be blown or there's a connection problem.
The green LED on Mini-Charger will light when there's current flow from Mini-Generator.
The green LED will light even if fuse is blown. A simple method of checking fuse is to turn on the light switch with bike not running.
NOTE:The photo is for demonstration only! Your connections will be neatly tucked away!
This photo illustrates how the LED tail light can be installed and connected.
The tail light is a 2.5" diameter rugged light with metal base and a beehive type lens.
The tail light should be attached to bicycle rear frame area by using fender attachment screw hole (as seen in photo).
An extra length of black 18g wire and connector terminals are provided for tail light installation.
Strips of duct tape can be used to fasten wire to bike frame. Wires can be either folded or cut shorter during arrangement.
Strips of tape matching bicycle frame color can also be used for a neater appearance. Wire can also be held in place on inner frames so they're not seen at all.
Colorful duct tape are available at most major hardward stores. A few 6 and 8" cable ties are included.
The wire connection seen in this photo is for illustration purpose only! Your results will certainly be better!
The photos below shows the actual LED headlight and tail light shining on the street.
The black oil mark on the street is approximately 30 feet ahead.
The lights are very energy efficient and will run for hours on a fully charged battery.
The LED headlight consist of a high power 3 Watt STAR Type LED bulb.
This LED headlight is a warm white light which makes it a similar to a regular halogen or other incandescent light.
It will outperform most regular dynamo type 6 volt light bulbs while using a smaller portion of energy.
LED bulbs are designed to last for thousands of hours, unlike regular light bulbs which blow out easily because of vibration.
LED light bulbs are more efficient than regular light bulbs because they don't waste a lot of energy producing heat.
NOTE: This headlight is a sealed unit. LED bulbs are not casually replaceable like regular bulbs.
PAYMENTS
All payments for auction items and "Buy Now" items are expected within 3 days, but no later than 7 days. Payments are accepted through Paypal only. If you click on "Buy Now" and then click on "Commit to Buy" you will be expected to complete the transaction by making payment. If payment is not made after three days the system is set to automatically remind you about payment on the fourth day. If no payment is made within 7 days the system is setup to automatically open a "Non-Payment case" against you.
If you're not sure about completing the payment just use the new shopping cart provided by eBay. This way you are not commited to pay if you change your mind or are unable to complete the process for some reason. In any event if you are unable to complete a "Buy it Now" commitment in a reasonable time, please contact me about it as a matter of courtesy and understanding. Serious inquiries about payment for individual items welcome.
SHIPPING
Flat rate shipping & handling price is available for the continental USA. Shipping & handling might also be the same for other states outside the continental United States. This item will normally ship within 2 business days, but could take up to 5 business days. To check shipping and handling fees to your state just click on the SHIPPING AND PAYMENTS button below top photo on this eBay page.
Items will be shipped to the address provided for transaction. Request to change shipping address after item is shipped will be ignored.
We reserve the right to refuse shipment to uncomfirmed addresses in which case the buyer's payment will be refunded. Insurance is included for some items based on our discretion.
INTERNATIONAL
shipment of these products are available to international customers but with slightly higher fees. These slightly higher fees are deemed necessary to cover the inherent risks involved in shipping products overseas which don't include precise delivery confirmation and can sometimes get lost. Some packages might require signature confirmation to prevent fraud.
United States Postal Service
(USPS)
First Class Mail
is usually the lowest rate but no tracking number is provided, however you
will
be notified when item ships.
USPS Priority Flat Rate
is sometimes a cheaper rate depending on the product involved. There is also no precise tracking number available for this service except to sometimes to indicate when the item is enroute to your country; however you
will
be notified when item ships.
USPS EXPRESS MAIL
is the only US Postal Service which provides complete tracking but cost much more than the other services. Multiple shipping options will be offered with each product.
INTERNATIONAL SHIPPING TIME
Most items shipped internationally will arrive within 10 to 14 business days but could take up to 28 days total based on customs delays in your country and/or holiday schedules. Please allow at least 21 days before contacting me about package arrivals.
PLEASE NOTE
Customs duty fees and any other fees applied to this product in your country is NOT included in the price of this product and will NOT be paid by us. You are expected to be familiar with any applicable import or custom fees associated with products imported into your country. To check shipping and handling fees to your country just click on the SHIPPING AND PAYMENTS button below top photo on this eBay page.
***** FEEDBACKS *****
Feedbacks are an important part of eBay purchasing and customer transaction experience. We would be happy to receive a positive feedback and five (5) star rating from all customers who are satisified with our products and/or services. Feedbacks are normally left for customers after a positive feedback is received to confirm a successful transaction.
If you are unsatisfied for any reason, please don't hesitate to contact me. We are always willing to resolve any problems you might have. Please don't resort to leaving a negative feedback before contacting us about a problem! We reserve the right to block customers who resort to negative feedbacks without first contacting us to resolve the problem or customers who are chronically problematic.
WARRANTY & RETURNS
The SUPER DYNO Lighting System (patent pending) is warrantied for 7 days cash back, and 30 days replacement. If you are unsatisfied for any reason, just return the complete kit, and a refund will be issued (less shipping and handling). Shipping & handling is not refundable, and the customer is responsible for shipping cost of the returned item.If any problems are experienced with our products, please contact us for assistance before resorting to any other course of action.
NOTE- Any item showing signs of tampering or abuse will void warranty!
INTERNATIONAL
customers are legible for the 30 days parts replacement warranty ONLY. Customer is responsible for shipping returned items.
DISCLAIMER
This "SUPER DYNO Lighting System", and all parts, pieces, ideas and designs associated therewith, are the proprietary rights and ownership of Wonderful Creations Store. Any copying, modifying, tampering and or false claims are discouraged and expressly prohibited.
By purchasing this system you agree to abide by any and all traffic laws governing your city, state or country and further agree to hold Wonderful Creations and any associates thereof, blameless for any accidents, mishaps, property loss, damages, death, injuries or expenses reportedly, or supposedly caused by the use, or misuse of this lighting system.
Copyright © 2004-2012 Wonderful Creations . All rights reserved.